Cnc Machine Design (Computer Numeric Control) Mini Plotter For Arduino Based Souvenir Craft
Keywords
Full Text:
PDFReferences
I. Alzusnan, J. Teknik, E. Politeknik, and N. Lhokseumawe, “RANCANG BANGUN SISTEM MONITORING LEVEL FLUIDA BERBASIS,†vol. 5, no. 1, pp. 15–20, 2021.
I. V. Choirony, M. S. Hariyanto, M. Ulum, A. Ubaidillah, H. Haryanto, and R. Alfita, “Rancang Bangun Acrylic Engraver and Cutting Machine Menggunakan CNC Milling 3 Axis Berbasis Mikrokontroler,†Elektrika, vol. 13, no. 1, p. 13, 2021, doi: 10.26623/elektrika.v13i1.3071.
S. Raad, H. Mohammad, and M. Falah, “Accurate and Cost-Effective Mini CNC Plotter,†Int. J. Comput. Appl., vol. 178, no. 48, 2019, doi: 10.5120/ijca2019919370.
I. D. Febryanto and S. D. Kartikasari, “PERANCANGAN MESIN CNC ROUTER 3 AXIS BERBASISKAN METODE QUALITY FUNCTION DEPLOYMENT ( QFD ),†vol. 17, no. 1, pp. 109–120, 2022.
H. Kusumo and S. Rakasiwi, “Information System Supply Chain Management with FIFO Pertetual Method,†Adv. Sustain. Sci. Eng. Technol., vol. 3, no. 2, 2021, doi: 10.26877/asset.v3i2.9722.
M. M. Hasan, M. R. Khan, A. T. Noman, H. Rashid, N. Ahrned, and S. T. Reza, “Design and Implementation of a Microcontroller Based Low Cost Computer Numerical Control (CNC) Plotter using Motor Driver Controller,†2019, doi: 10.1109/ECACE.2019.8679123.
J. E. Bresenham, “Algorithm for computer control of a digital plotter,†IBM Syst. J., vol. 4, no. 1, 2010, doi: 10.1147/sj.41.0025.
V. F. Goszal, H. H. Nuha, and M. Abdurohman, “Manufacturing a Plotter Printer with Computer Numerical Control Based Pen Ink Using CoreXY Mechanisms,†J. MEDIA Inform. BUDIDARMA, vol. 5, no. 2, 2021, doi: 10.30865/mib.v5i2.2783.
E. Poustinchi, “Subtractive digital fabrication with actual robot and virtual material using a MARI platform,†Int. J. Archit. Comput., vol. 16, no. 4, 2018, doi: 10.1177/1478077118801594.
A. Örtorp and T. Jemt, “Clinical experiences of computer numeric control-milled titanium frameworks supported by implants in the edentulous jaw: A 5-year prospective study,†Clin. Implant Dent. Relat. Res., vol. 6, no. 4, 2004, doi: 10.1111/j.1708-8208.2004.tb00036.x.
D. Mejia, A. Moreno, A. Arbelaiz, J. Posada, O. Ruiz-Salguero, and R. Chopitea, “Accelerated Thermal Simulation for Three-Dimensional Interactive Optimization of Computer Numeric Control Sheet Metal Laser Cutting,†J. Manuf. Sci. Eng. Trans. ASME, vol. 140, no. 3, 2018, doi: 10.1115/1.4038207.
L. Luo, Z. X. Yang, L. Tang, and K. Zhang, “An ELM-Embedded Deep Learning Based Intelligent Recognition System for Computer Numeric Control Machine Tools,†IEEE Access, vol. 8, 2020, doi: 10.1109/ACCESS.2020.2965284.
DOI: https://doi.org/10.26877/asset.v4i1.11648
Refbacks
- There are currently no refbacks.

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.